Wear Analysis of Mine Equipment

Jump To References Section

Authors

  • Ashwani Kumar
     Department of Mechanical Engineering, Indian School of Mines, Dhanbad ,IN
  • Rajeev Kumar
     Department of Mechanical Engineering, Indian School of Mines, Dhanbad ,IN
  • Subrata Kumar Ghosh
     Department of Mechanical Engineering, Indian School of Mines, Dhanbad ,IN

Keywords:

Mine Equipment, Wear, Wear Modes, Lube Oil.

Abstract

A fundamental overview of developments and progress of mathematical models for quantitative estimation of wear in lubricated system are discussed in terms of practical problem of HEMM equipment. A review on extensive modes of wear and their reason is also presented. Their mathematical models related to wear particle concentration, wear rate, total wear, severity of wear, severity Index and total wear amount is considered. The purpose of this paper is to provide an outline of developments taken place over the past three decades, in the field of quantitative estimation of wear debris.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2022-10-17

How to Cite

Kumar, A., Kumar, R., & Ghosh, S. K. (2022). Wear Analysis of Mine Equipment. Journal of Mines, Metals and Fuels, 64(5), 233–235. Retrieved from https://informaticsjournals.com/index.php/jmmf/article/view/31524

Issue

Volume 64, Issue 5, May 2016

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

 

References

Kjer, T. (1981): “Wear Rate and Concentration of Wear Particles in Lubricating Oil,” Wear, vol. 67, pp. 217-226, 1981.

Iwa, Y. , Hond, T., Miyajim, T., Yoshinag, S., Higash, M. and Fuw, Y. (2010): “Quantitative estimation of wear amounts by real time measurement of wear debris in lubricating oil,” Tribology International, vol. 43, pp. 388-394, 2010.

Yuansheng,, J. and Qjming, Y. (1984): “Ferrograhic Analysis of Wear Debris Generated in Locomotive Diesel Engines,” Wear, vol.93, pp. 23-32, 1984.

Macian, V., Payri, R., Tormos, B. and Montoro, L. (2006): “Applying analytical ferrography as a technique to detect failures in Diesel engine fuel injection systems,” Wear, vol. 260, pp. 562-566, 2006.

Roylance, B. J. and Raadnui, S. (1994): “The morphological attributes of wear particles their role in identifying wear mechanisms,” Wear, vol. 175, pp. 115-12, 1994.

Hofman, M. V. and Johnson, J. H. (1977): “The Development of Ferrography as a Laboratory Wear Measurement Method For The Study of Engine Operating Conditions on Diesel Engine Wear,” Wear, Vol. 44, pp. 183-199, 1977.

Scherge, M., Martin, J. M. and Pohlmann, K. (2006): “Characterization of wear debris of systems operated under low wear-rate conditions,” Wear, Vol. 260, pp. 458-46, 2006.

Needelman, W. and Madhavan, P. (1988): “Review of lubricant contamination and diesel engine wear,” SAE, 881827, 1988.

Vencl, A. and Rac, A. (2014): “Diesel engine crankshaft journal bearings failures: Case study,” Engineering Failure Analysis, vol. 44, pp. 217-228, 2014.

Pujatt, M., Suhadol, M. and Piculi, D. (2014): “Fretting-initiated fatigue in large bore engines connecting rods,” Procedia Engineering, vol.74, pp. 356-359, 2014.

Sjodin, U. I. and Olofsson, U. L. O. (2003): “Initial sliding wear on piston rings in a radial piston hydraulic motor,” Wear, vol. 254, pp. 1208-1215, 2003.

Michalski, J. and Wos, P. (2011): “The effect of cylinder liner surface topography on abrasive wear of piston-cylinder assembly in combustion engine,” Wear, Vol. 271, pp. 582-589, 2011.

Anderson, D. P. and Driver, R. D. (1979): “Equilibrium particle concentration in engine oil,” Wear, vol. 56, pp. 415-419, 1979.

Scott, D., Mc Cullagh, P. J. and Campbell, G. W. (1978): “Condition Monitoring of Gas Turbines – An Exploratory Investigation of Ferrographic Trend Analysis,” Wear, Vol. 49, pp. 373-389, 1978.