Mechanical Wear of Cutters in Tunnel Boring Machines – A Comprehensive Review

Jump To References Section

Authors

  • CSIR-Central Institute of Mining and Fuel Research, Nagpur Research Centre, 17/C Telangkhedi Area, Civil Lines, Nagpur 440001 ,IN
  • CSIR-Central Institute of Mining and Fuel Research, Nagpur Research Centre, 17/C Telangkhedi Area, Civil Lines, Nagpur 440001 ,IN
  • CSIR-Central Institute of Mining and Fuel Research, Nagpur Research Centre, 17/C Telangkhedi Area, Civil Lines, Nagpur 440001 ,IN
  • CSIR-Central Institute of Mining and Fuel Research, Nagpur Research Centre, 17/C Telangkhedi Area, Civil Lines, Nagpur 440001 ,IN
  • CSIR-Central Institute of Mining and Fuel Research, Nagpur Research Centre, 17/C Telangkhedi Area, Civil Lines, Nagpur 440001 ,IN
  • Department of Mining Engineering, IIT(ISM), Dhanbad 826004 ,IN

Keywords:

Factors that determine the selection of method to excavate a tunnel depend upon the geology, economy and site conditions,but when it comes to the economics of tunnelling then it has to be chosen correctly as per the methodology. Cutters are an integral part of a tunnel boring machine and its performance depends largely on these. In order to ascertain various factors of cutters that influence the performance of the machine, a comprehensive study of literature was carried out. The method involved referencing the citations to a particular publication from which the importance of factors responsible for cutter wear in TBM were decided. In order to categorise the impact of different variables on cutter wear, the references were divided into wear, mechanical, geological and engineering categories based on citations reviewed and observed. Cutting conditions of disc cutters has been reviewed and evaluated based on findings of different authors.

Abstract

Factors that determine the selection of method to excavate a tunnel depend upon the geology, economy and site conditions,but when it comes to the economics of tunnelling then it has to be chosen correctly as per the methodology. Cutters are an integral part of a tunnel boring machine and its performance depends largely on these. In order to ascertain various factors of cutters that influence the performance of the machine, a comprehensive study of literature was carried out. The method involved referencing the citations to a particular publication from which the importance of factors responsible for cutter wear in TBM were decided. In order to categorise the impact of different variables on cutter wear, the references were divided into wear, mechanical, geological and engineering categories based on citations reviewed and observed. Cutting conditions of disc cutters has been reviewed and evaluated based on findings of different authors.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2022-10-20

How to Cite

Deshmukh, S., Raina, A., Pandey, P., Vajre, R., Trivedi, R., & Murthy, V. (2022). Mechanical Wear of Cutters in Tunnel Boring Machines – A Comprehensive Review. Journal of Mines, Metals and Fuels, 67(9), 391–402. Retrieved from https://informaticsjournals.com/index.php/jmmf/article/view/31648

 

References

Acaroglu, O., Ozdemir, L. and Asbury, B., (2008): A fuzzy logic model to predict specific energy requirement for TBM performance prediction. Tunnelling and Underground Space Technology, 23(5), pp.600-608.

Adoko, A.C., Jiao, Y.Y., Wu, L., Wang, H. and Wang, Z.H., (2013): Predicting tunnel convergence using multivariate adaptive regression spline and artificial neural network.

Tunnelling and Underground Space Technology, 38, pp.368-376.

Alber, M., (2008): Stress dependency of the Cerchar abrasivity index (CAI) and its effects on wear of selected rock cutting tools. Tunnelling and underground space technology, 23(4), pp.351-359.

Archard, J., (1953): Contact and rubbing of flat surfaces. Journal of applied physics, 24(8), pp.981-988.

Ates, U., Bilgin, N., & Copur, H. (2014): Estimating torque, thrust and other design parameters of different type TBMs with some criticism to TBMs used in Turkish tunneling projects. Tunnelling and Underground Space Technology, 40, 46–63.

Barton, N.R., (2000): TBM tunnelling in jointed and faulted rock. CRC Press.pp.9 7. Benardos, A., (2008): Artificial intelligence in underground development: a study of TBM performance. Underground Spaces: Design, Engineering and Environmental Aspects, 102, p.121.

Benardos, A.G. and Kaliampakos, D.C., (2004): Modelling TBM performance with artificial neural networks. Tunnelling and Underground Space Technology, 19(6), pp.597-605.

Benato, A., Oreste, P., (2015): Prediction of penetration per revolution in TBM tunneling as a function of intact rock and rock mass characteristics. Int. J. Rock Mech. Min. Sci. 74, 119-127.

Bieniawski, Z.T., Celada, B., Galera, J.M. and Tardáguila, I., (2009): Prediction of cutter wear using RME.

Universidad Politecnica de Madrid, Spain.

Bilgin, N., Balci, C., Copur, H, Tumac, D., Avunduk, E, 2012b, Rock Mechanics Aspects Related to Cutting Efficiency of Mechanical Excavators, 25 Years of Experience in Istanbul. Eurock 2012, Stockholm 12. Bruland, A., 1998. Hard rock tunnel boring: Drillability test methods. Project report 13A-98, NTNU Trondheim, 8, 1-21.

Büchi, E., (1984): Einfluss geologischer Parameter auf die Vortriebsleistungeiner Tunnel bohrmaschine. Inaugural dissertation, Philosophisch- naturwissenschaftliche Fakultät, Universität Bern, p. 136.

Cigla, M., Yagiz, S. and Ozdemir, L., (2001): Application of tunnel boring machines in underground mine development. In 17th international mining congress and exhibition of Turkey (pp. 155-164).

Cook, N.G.W., Hood, M. and Tsai, F., (1984): April. Observations of crack growth in hard rock loaded by an indenter. In International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts (Vol. 21, No. 2, pp. 97-107). Pergamon.

Dahl, F., Grøv, E. and Breivik, T., (2007): Development of a new direct test method for estimating cutter life, based on the Sievers’ J miniature drill test. Tunnelling and Underground Space Technology, 22(1), pp.106-116.

Delisio, A., Zhao, J. and Einstein, H.H., (2013): Analysis and prediction of TBM performance in blocky rock conditions at the Lötschberg Base Tunnel. Tunnelling and Underground Space Technology, 33, pp.131-142.

Dual Mode, “Crossover” Type Tunnel Boring Machines: A Unique Solution for Mixed Ground in the Middle East Tyler D. Sandell the Robbins Company, [Accessed on 12 June 2018]

Eftekhari, M., Baghbanan, A. and Bayati, M., (2010): January. Predicting penetration rate of a tunnel boring machine using artificial neural network. In ISRM International Symposium-6th Asian Rock Mechanics Symposium. International Society for Rock Mechanics.

Evans, A.G., Marshall, D.B., (1981): Wear mechanisms in ceramics. In: Rigney, D.A. (Ed.), Fundamentals of Friction and Wear of Materials. American Society for Metals, Metals Park, Ohio, pp. 438-452.

Ewendt, D., (1992): Erfassung der Gesteinsabrasivität und Prognose des Werkzeugvers chlei ßesbeimmaschinellen Tunnel vortriebmit Diskenmeißeln. Kurzberichteaus der Bauforschung, 33, p.9 22. Farmer, I.W., Glossop, N.H., (1980): Mechanics of disc cutter penetration. Tunnels Tunnell. Int. 12 (6), pp.22-25.

Fattahi, H. and Babanouri, N., (2017): Applying optimized support vector regression models for prediction of tunnel boring machine performance. Geotechnical and Geological Engineering, 35(5), pp.2205-2217.

Frenzel, C., (2011): January. Disc cutter wear phenomenology and their implications on disc cutter consumption for TBM. In 45th US Rock Mechanics/ Geomechanics Symposium. American Rock Mechanics Association. pp.26-29

Frenzel, C., Käsling, H. and Thuro, K., (2008): Factors influencing disc cutter wear. Geomechanik und Tunnelbau: Geomechanik und Tunnelbau, 1(1), pp.55-60.

Gehring, K., 1995. Prognosis of advance rates and wear for underground mechanized excavations. Felsbau, 13(6), pp.439-448.

Girmscheid, G. and Schexnayder, C., (2003): Tunnel boring machines. Practice periodical on structural design and construction, 8(3), pp.150-163.

Gong, Q. and Zhao, J., (2009): Development of a rock mass characteristics model for TBM penetration rate prediction. International journal of Rock mechanics and mining sciences, 46(1), pp.8-18.

Gong, Q.M., She, Q.R. and Ding, Y., (2012): Abrasivity Tests of Marbles and Cutter Wear Analysis of TBM: Headrace Tunnels of Jinping a! Hydropower Station [J]. Journal of Beijing University of Technology, 8, p.017.

Gong, Q.M., Zhao, J., (2009): Development of a rock mass characteristics model for TBM penetration rate prediction. Int. J. Rock Mech. Min. Sci. 46(1), 8-18.

Goryacheva, I.G. and Goryachev, A.P., (2006). The wear contact problem with partial slippage. Journal of applied mathematics and mechanics, 70(6), pp.934-944.

Goryacheva, I.G. and Mezrin, A.M., (2011): Simulation of combined wearing of the shaft and bush in a heavily loaded sliding bearing. Journal of Friction and Wear, 32(1), pp.1-7.

Graham, P.C., (1976): Rock exploration for machine manufacturers. In: Bieniawski, Z.T. (Ed.), Exploration for Rock Engineering. Balkema, Johannesburg, pp. 173–180.

Grima, M.A., Bruines, P.A. and Verhoef, P.N.W., (2000): Modeling tunnel boring machine performance by neurofuzzy methods. Tunnelling and Underground Space Technology, 15(3), pp.259-269.

Hamidi, J.K., Shahriar, K., Rezai, B. and Bejari, H., (2010): Application of fuzzy set theory to rock engineering classification systems: an illustration of the rock mass excavability index. Rock mechanics and rock engineering, 43(3), pp.335-350.

Hamidi, J.K., Shahriar, K., Rezai, B. and Rostami, J., (2010): Performance prediction of hard rock TBM using Rock Mass Rating (RMR) system. Tunnelling and Underground Space Technology, 25(4), pp.333-345.

Hassanpour, J., Rostami, J., Azali, S.T. and Zhao, J., (2014): Introduction of an empirical TBM cutter wear prediction model for pyroclastic and mafic igneous rocks; a case history of Karaj water conveyance tunnel, Iran. Tunnelling and Underground Space Technology, 43, pp.222-231.

Hassanpour, J., Rostami, J., Khamehchiyan, M. and Bruland, A., (2009): Developing new equations for TBM performance prediction in carbonate-argillaceous rocks: a case history of Nowsood water conveyance tunnel. Geomechanics and Geoengineering: An International Journal, 4(4), pp.287-297.

He, X.X. and Wu, Q.M., (2007): Intelligent decision support system of type selection for tunnel boring machine. Journal of the China Railway Society, 29(3), pp.127-131.

Hughes, H.M., (1986): The relative cuttability of coalmeasures stone. Mining science and Technology, 3(2), pp.95-109.

Ignesti, M., Malvezzi, M., Marini, L., Meli, E. and Rindi, A., (2012): Development of a wear model for the prediction of wheel and rail profile evolution in railway systems. Wear, 284, pp.1-17.

Iphar, M., (2012): ANN and ANFIS performance prediction models for hydraulic impact hammers. Tunnelling and Underground Space Technology, 27(1), pp.23-29.

Javad, G. and Narges, T., (2010): Application of artificial neural networks to the prediction of tunnel boring machine penetration rate. Mining Science and Technology (China), 20(5), pp.727-733.

Jiang, A.N., Wang, S.Y. and Tang, S.L., (2011): Feedback analysis of tunnel construction using a hybrid arithmetic based on Support Vector Machine and Particle Swarm Optimisation. Automation in Construction, 20(4), pp.482489.

Johnson, K.L., (2009): Contact mechanics. Proceedings of the Institution of Mechanical Engineers Part J-Journal of Engineering Tribology, 223(J3), pp.254-254.

Kim, T., (2004): Development of a fuzzy logic based utilization predictor model for hard rock tunnel boring machines (Doctoral dissertation, Colorado School of Mines).

Liu, Q., Liu, J., Pan, Y., Zhang, X., Peng, X., Gong, Q. and Du, L., (2017): A wear rule and cutter life prediction model of a 20-in. TBM cutter for granite: a case study of a water conveyance tunnel in China. Rock Mechanics and Rock Engineering, 50(5), pp.1303-1320.

Mahdevari, S. and Torabi, S.R., (2012): Prediction of tunnel convergence using artificial neural networks. Tunnelling and Underground Space Technology, 28, pp.218-228.

Mahdevari, S., Shahriar, K., Yagiz, S. and Shirazi, M.A., (2014): A support vector regression model for predicting tunnel boring machine penetration rates. International Journal of Rock Mechanics and Mining Sciences, 72, pp.214-229.

Maidl, B., Schmidz, L., Ritz, W., Herrenknecht, M., (2008): Hard Rock Tunnel Boring Machines. Ernst and Sohn, Berlin, p. 343.

Man, Lin Tao, and Shou Ju Li. (2011): “Numerical Simulation of Rock Fragmentation Process Induced by Two Disc Cutters”, Advanced Materials Research.

Matern, N. von, Hjelme ìr, A., 1963, Forsøk med pa grus. StatensVa ginstitut, Medelande nr. 65, Stockholm.

Medel-Morales, R.C. and Botello-Rionda, S., (2013): Design and optimization of tunnel boring machines by simulating the cutting rock process using the discrete element method, 17(3), pp.329-339.

Minh, V.T., Katushin, D., Antonov, M. and Veinthal, R., (2017): Regression Models and Fuzzy Logic Prediction of TBM Penetration Rate. Open Engineering, 7(1), pp.60-68.

Miranda, T.F., (2007): Geomechanical parameters evaluation in underground structures: artificial intelligence, bayesian probabilities and inverse methods.

Naghadehi, M.Z. and Mikaeil, R., (2017): Optimization of tunnel boring machine (TBM) disc cutter spacing in jointed hard rock using a distinct element numerical simulation. Periodica Polytechnica. Civil Engineering, 61(1), p.56.

Niniæ, J. and Meschke, G., (2015): Model update and realtime steering of tunnel boring machines using simulationbased meta models. Tunnelling and Underground Space Technology, 45, pp.138-152.

Ocak, I., Bilgin, N., (2009): The performance of two EBP Machines in Istanbul MetroTunneldrivages in soft and shallow ground. ITA-AITES World Tunnel CongressBudapest, Hungary, 23–28 May, 8p.

Oparin, V.N. and Tanaino, A.S., (2015): A new method to test rock abrasiveness based on physico-mechanical and structural properties of rocks. Journal of Rock Mechanics and Geotechnical Engineering, 7(3), pp.250-255.

Ozdemir, L., (1977): Development of theoretical equations for predicting tunnel boreability (Doctoral dissertation, Colorado School of Mines. Arthur Lakes Library).

Pang, S.S., Goldsmith, W. and Hood, M., (1989): A forceindentation model for brittle rocks. Rock Mechanics and Rock Engineering, 22(2), pp.127-148.

Petrica, M., Badisch, E. and Peinsitt, T., (2013): Abrasive wear mechanisms and their relation to rock properties. Wear, 308(1-2), pp.86-94.

Rabinowicz, E., (1995): Friction and Wear of Materials, Second ed. Willy, New York.

Roby, J., Sandell, T., Kocab, J. and Lindbergh, L., (2008): The current state of disc cutter design and development directions.

Rostami, J., (1997): Development of a force estimation model for rock fragmentation with disc cutters through theoretical modeling and physical measurement of crushed zone pressure (Doctoral dissertation, Colorado School of Mines).

Rostami, J., (1997): Development of a force estimation model for rock fragmentation with disc cutters through theoretical modeling and physical measurement of crushed zone pressure (Doctoral dissertation, Colorado School of Mines), pp. 249.

Rostami, J., Ozdemir, L. and Nilson, B., (1996): May. Comparison between CSM and NTH hard rock TBM performance prediction models. In Proceedings of Annual Technical Meeting of the Institute of Shaft Drilling Technology, Las Vegas (pp. 1-10).

Rostami, J., Ozdemir, L. and Nilson, B., (1996): May. Comparison between CSM and NTH hard rock TBM performance prediction models. In Proceedings of Annual Technical Meeting of the Institute of Shaft Drilling Technology, Las Vegas, pp. 1-10

Rostami, J., Ozdemir, L., (1993): A new model for performance prediction of hard rock TBM. In: Bowerman, L.D. et al. (Eds.), Proceedings of RETC, Boston, MA, pp. 793-809.

Roxborough, F.F. and Phillips, H.R., (1975): December. Rock excavation by disc cutter. In International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts (Vol. 12, No. 12, pp. 361-366). Pergamon.

Roxborough, F.F., (1985): June. Research in mechanical rock excavation: progress and prospects. In Proceedings of the Rapid Excavation and Tunnelling Conference (Vol. 1, pp. 225-243).

Ruwanpura, J.Y., AbouRizk, S.M. and Allouche, M., (2004): Analytical methods to reduce uncertainty in tunnel construction projects. Canadian Journal of Civil Engineering, 31(2), pp.345-360.

Salimi, A. and Esmaeili, M., (2013): Utilising of linear and non-linear prediction tools for evaluation of penetration rate of tunnel boring machine in hard rock condition. International Journal of Mining and Mineral Engineering, 4(3), pp.249-264.

Salimi, A., Moormann, C., Singh, T. and Jain, P., (2015): November. TBM performance prediction in rock tunneling using various artificial intelligence algorithms. In Regional tunneling conference tunnels and the future (pp. 34-43).

Salimi, A., Rostami, J. and Moormann, C., (2017): Evaluating the suitability of existing rock mass classification systems for TBM performance prediction by using a regression tree. Procedia Engineering, 191, pp.299-309.

Sandell, T.D. and Stypulkowski, J., (2015): Dual Mode,”Crossover” Type Tunnel Boring Machines: A Unique Solution for Mixed Ground in the Middle East. In Proc. of the Arabian Tunnelling Conference (pp. 1-13).

Sanio, H.P., (1985): June. Prediction of the performance of disc cutters in anisotropic rock. In International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts (Vol. 22, No. 3, pp. 153-161). Pergamon.

Sievers, H., (1950): Die Bestimmung des BohrwiderstandesvonGesteinen, Glu ckauf 86: 37/38, Guckauf G.M.B.H., Essen, pp.776–784

Snowdon, R.A., Ryley, M.D. and Temporal, J., (1983): April. A study of disc cutting in selected British rocks: Reply to the Discussion by HK Kutter and H.-P-Sanio of the paper by RA Snowdon, MD Ryley and J. Temporal, Int. J. Rock Mech. Min. Sci. & Geomech. Abstr. 19, 107–121 (1982). In International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts (Vol. 20, No. 2, p. 105). Pergamon.

Suh, N.P., (1973): The delaminating theory of wear. Wear 25 (1), 111-124.

Sun, W., Huo, J., Chen, J., Li, Z., Zhang, X., Guo, L., Zhao, H. and Zhao, Y., (2011): Disc cutters’ layout design of the full-face rock tunnel boring machine (TBM) using a cooperative coevolutionary algorithm. Journal of Mechanical Science and Technology, 25(2), pp.415-427.

Tiryaki, B., (2008). Application of artificial neural networks for predicting the cuttability of rocks by drag tools. Tunnelling and Underground Space Technology, 23(3),pp.273-280.

Villeneuve, M., Using Tunnel Boring Machine Penetration Tests to Quantify Performance in Hard Rock.

Von Preinl, Z.T., Tamames, B.C., Fernandez, J. and Hernandez, M.A., (2006): Rock mass excavability indicator: New way to selecting the optimum tunnel construction method. Tunnelling and underground space technology, 21, pp. 3-4.

Wang, L., Kang, Y., Zhao, X. and Zhang, Q., (2015): Disc cutter wears prediction for a hard rock TBM cutterhead based on energy analysis. Tunnelling and Underground Space Technology, 50, pp.324-333.

Wang, L., Li, H., Zhao, X. and Zhang, Q., (2017): Development of a prediction model for the wear evolution of disc cutters on rock TBM cutterhead. Tunnelling and Underground Space Technology, 67, pp.147-157.

West, G., (1989): Rock abrasiveness testing for tunnelling. Int. J of Rock Mech & Mining Sci & Geomechanic Abs, 26(2).

Wijk, G., (1992): A model of tunnel boring machine performance. Geotechnical & Geological Engineering, 10(1), pp.19-40.

Wijk, G., (1992): A model of tunnel boring machine performance. Geotechnical & Geological Engineering, 10(1), pp.19-40.

Yagiz, S. and Karahan, H., (2011): Prediction of hard rock TBM penetration rate using particle swarm optimization. International Journal of Rock Mechanics and Mining Sciences, 48(3), pp.427-433.

Yagiz, S., Gokceoglu, C., Sezer, E. and Iplikci, S., (2009): Application of two non-linear prediction tools to the estimation of tunnel boring machine performance. Engineering Applications of Artificial Intelligence, 22(4-5), pp.808-814.

Yagiz, S., Merguerian, C. and Kim, T., (2010): May. Geological controls on the breakthrough of tunnel boring machines in hard rock crystalline terrains. In Eurock (pp. 401-404).

Yang, Y.D., Chen, K., Li, F.Y. and Zhou, J.J., (2015): Wear prediction model of disc cutter. J China Coal Soc, 40(6), pp.1290-1296.

Yazdani-Chamzini, A. and Yakhchali, S.H., (2012): Tunnel Boring Machine (TBM) selection using fuzzy multicriteria decision making methods. Tunnelling and Underground Space Technology, 30, pp.194-204.

Yifa, W.A.N.G., (2000): Prospect of Artificial Intelligence on Drilling System. Petroleum Drilling Techniques, 28(2), pp.36-38.

Zertsalov, M.G. and Deineko, A.V., (2005): January. The engineering rock mass classification on the basis of numerical analysis of static interaction of underground openings and rock masses (applied for TBM tunnels). In Alaska Rocks 2005, The 40th US Symposium on Rock Mechanics (USRMS). American Rock Mechanics Association.

Zhang, Q., Kang, Y., Zheng, Z. and Wang, L., (2013): Inverse analysis and modeling for tunneling thrust on shield machine. Mathematical Problems in Engineering, 2013.

Zhao, J. and Gong, Q.M., (2006): Rock mechanics and excavation by tunnel boring machine–issues and challenges. In Rock Mechanics in Underground Construction: (With CD-ROM) (pp. 83-96).

Zheng, Y.L., Zhang, Q.B. and Zhao, J., (2016): Challenges and opportunities of using tunnel boring machines in mining. Tunnelling and Underground Space Technology, 57, pp.287-299.

WWW references

http://www.nfm-technologies.com/-Soft-groundmachines-.html[Accessed on 13 June2018]

http://www.nzgs.org/library/ nzgs20_villeneuve/[Accessed on 15 June 2018]

http://www.sapparts.com/downloads/TBM% 20 Cutter%20 Roller% 20 (New%20 Versions).p df [Accessed on 15 June 2018]

http://www.therobbinscompany.com/ hybrid-tbms-blo/ [Accessed on 12 June 2018]

http://ïðîìêàòàëîã.ðô/ Public Documents/ 1200681.pdf [Accessed on 15 June 2018]

https://en.wikipedia.org/wiki/Category: Tunnels_in_India [Accessed on 15 June2018]

https://pdfs.semanticscholar.org/1595/25130ac4e02cab6cf 2400f 1b053fd 3882155.pdf?_ga =

.229296732.1787020089.1533533277-1751588432.1533533277 [Accessed on 11 June2018]

https://www.alptransit.ch/fileadmin/dateien/media/zahlen_und_fakten/Data_Tunnel boringmachine_e.pdf [Accessed on 11 June 2018]

https://www.google.co.in/search?q= Different+types+of+TBM+ cutters & tbm= isch&tbo=u&source=univ&sa= X&ved= 0ah UKEwi BxM254r WAh VLNo8 KHU9tAMwQsAQIXw&biw= 1138&bih= 549#imgrc= ijC8VGCTt3 DghM [Accessed on 11 June 2018]

https://www.google.co.in/search?q = HYBRID+ TBM+Thrust,+ Torque,+ RPM & client= firefoxb&dcr= 0&tbm=isch&tbo= u&source= univ&sa= X&ved= 0ahUKEwiKwuDpk6f ZAhXLpo8 KHY5GAUIQs AQIJw&biw =

&bih = 654 [Accessed on 12 June 2018]

https://www.herrenknecht.com/ en/ products/ additionalequipment/tunnelling-logistics/ excavation-tools.html

[Accessed on 15 June 2018]

https://www.slideshare.net/ redeyeshayat/ internshipreport-geological- engg-uet- lahore-2 [Accessed on 11 June2018]

https://www.slideshare.net/ VISHALKUMARSINGH1/report-for- tunnelling- by-tunnel- boring-machine

[Accessed on 11 June2018]

https://www.tunneltalk.com/ Czech-Republic- 06 Jun-2016- Ejpovice- tunnel-first- breakthrough.php [Accessed on 13 June 2018]