FEA and Experimental Investigation of Prosthetic Knee Joint

Jump To References Section

Authors

  • C. Shashishekar
     1Associate ProfessorDepartment of Mechanical Engineering, Siddaganga Institute of Technology, Tumakuru ,IN
  • S. J. Sanjay
     Research Scholar, Department of Mechanical Engineering, Siddaganga Institute of Technology, Tumakuru ,IN
  • Shreekant M.T
     P.G. Student, Mechanical Engineering Department, Basaveshwar Engineering College, Karnataka ,IN

DOI:

https://doi.org/10.18311/jmmf/2022/31994

Keywords:

Finite element analysis, Polariscope, Knee joint, Tibial, Femur, Flexion angle, Sagittal radius

Abstract

The aim of this study is to look at how stresses are distributed in a polyethylene-based prosthetic knee joint. Ansys 18.1 software is used for finite element analysis. In experimental studies, the effects of sagittal radius, flexion angle, and external load on knee joint stresses were investigated. The prosthetic knee joint is created as a 2D model using parameters like sagittal radius and flexion angles in design modeling software. The experimental work has been carried out in a polariscope machine setup, The photo elastic model is tested in different loading conditions and finds stress in that model. Finally, results are validated experimental results with FEA results.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

Downloads

Published

2022-12-08

How to Cite

Shashishekar, C., Sanjay, S. J., & M.T, S. (2022). FEA and Experimental Investigation of Prosthetic Knee Joint. Journal of Mines, Metals and Fuels, 70(8A), 332–338. https://doi.org/10.18311/jmmf/2022/31994

Issue

Volume 70, Issue 8A, August 2022

Section

Articles

License

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Crossref
Scopus
Google Scholar
Europe PMC

 

References

Farshad Vatankhahan, Moeinoddin, “Resistance analysis of Tibia bone on upper, midella and terminal sections by compressive strength testing and FEM”. Journal of Biomechanics, 2016 Volume: 2: PP: 345.

Ali M.Alsamhan, “Rationale analysis of human artificial knee replacements”, Journal of King Saud University - Engineering Sciences, 2013, Volume: 25, Issue: 1, PP: 49-54. DOI: https://doi.org/10.1016/j.jksues.2011.12.002

Shivaprasad. P. H and S. J. Sanjay, “Experimental Analysis of Prosthetic Knee Joint”,2020. International Journal of Advanced Research in Science & Technology (IJARST) Volume 8, Issue 1, DOI: XX.072020/IJARST

C. Shashishekar, Prashanta, and S.J. Sanjay “Experimental Analysis of Prosthetic Knee Joint”, 2021. International Advanced Research Journal in Science, Engineering and Technology volume 8, Issue 9, DOI:10.17148/IARJSET.2021.8913 DOI: https://doi.org/10.17148/IARJSET.2021.8913

Enab, T.A. and N.E. Bondok, “Material selection in the design of the tibia tray component of cemented artificial knee using finite element method. Materials & Design”, 2013. 44: PP: 454- 460. DOI: https://doi.org/10.1016/j.matdes.2012.08.017

Dr. C. Shashishekar, and S. J. Sanjay “Experimental Stress Analysis of Prosthetic Knee Joint - A Review”, 2021. International Journal of Innovative Research in Electrical, Electronics, Instrumentation, and Control Engineering, Volume 9, Issue 10, DOI: 10.17148/IJIREEICE.2021.91011 DOI: https://doi.org/10.17148/IJIREEICE.2021.91011

G. Mallesh and Sanjay. S.J “Finite Element Modelling and Analysis of Prosthetic Knee Joint” 2012. International Journal of Emerging Technology and Advanced Engineering, ISSN 2250- 2459, Volume 2, Issue 8, August 2012), PP. 264-269.